What to do About Electromagnetic Interference in Hospitals
By: Julia Aidan
Submitted: 2012-01-06 22:26:44 | Word Count: 866
With the assimilation of wireless communication technology into hospital infrastructures, hospitals are becoming concerned about the impact of radio frequency (RF) electromagnetic interference (EMI) between wireless technologies and medical equipment. Such interference may cause undesirable changes to medical equipment, possibly resulting in misdiagnosis, mistreatment, and/or patient injury.
These wireless communication devices include: wireless Local Area Networks (LAN), Bluetooth, wireless telecommunications, paging, two-way radios, telemetry devices, cell phones, wireless Personal Digital Assistants (PDA), and PC tablets/laptops. While most medical devices are manufactured now with a recommended 3V/m (10V/m for life support devices) immunity level against interference from RF emissions (IEC 60601-1-2), older equipment may have inadequate shielding and, therefore, be more susceptible to interference.
[ advertisement ]
Electromagnetic interference with electronic circuits can be dangerous in many ways. As a result, for many years, military, aircraft, and automotive electronics systems have been required to meet strict RFI requirements for immunity to up to 200 V/m, because these systems could encounter such levels during normal operations. The technology has already been developed to "harden" most medical devices against fields that are much more intense than the 3 V/m level specified in present RFI standards for medical devices. Most hardening techniques are not costly if they are incorporated into the initial design of the electronics system. Standard RF immunization techniques include the use of shielding, grounding and filtering. Shielding includes enclosing the device in metal boxes or in plastic boxes coated with metallic paint.
Grounding of electronics circuitry and cable shields is an inexpensive but necessary step toward ensuring RFI immunity. RF filtering of signal carrying conductors, especially in sensitive patient monitoring equipment, should be performed carefully. The potential for the success of these techniques has been demonstrated in implanted cardiac pacemakers, which commonly achieve immunity of up to 200 V/m, even though these devices monitor weak electrophysiological voltages.
The use of RF filters preceding the input circuitry of an implanted medical device is uncomplicated and basic. However, patient-connected medical devices, which are powered by an AC line, must accommodate the safety requirements for electrical leakage currents, as well as RFI immunity requirements. Therefore, patient connection leads on devices that obtain power from AC lines must utilize special techniques to simultaneously meet both types of safety requirements. Techniques for isolating patients, which incorporate optical or transformer coupling, may be required. In addition, designers can add interference recognition and fail-safe circuitry to their medical devices. For example, many cardiac pacemakers are protected from erratic operation by being programmed to revert to a fixed rate when RFI is detected.
Mobile RF and wireless communications systems can be optimized for compatibility with medical electronics. The modulation frequencies of RF transmitters should be outside the physiological passband of most or all medical devices. Digital modulation schemes that use time division multiple access (TDMI) and the associated amplitude modulation pulses, should be carefully designed to avoid RFI. Frequency modulation, or non-pulsed, spread spectrum modulation techniques, such as certain forms of code division multiple access (CDMA) can be used.
Managers of facilities where sensitive medical devices are used should control RFI by careful planning and system design. For example, the radiated power of many modern handheld and portable cellular phones is under the control of the base station. When close to a base station, handheld and portable phones may operate at power levels far lower than the maximum power of 600 miliWatt (for handheld phones) or 3 Watt (for portable phones). Thus, when a base station is located near a health care facility or when low power base stations (microcells) are used within the facility, cellular phones will normally operate at low power. However, the base station itself must be properly sited to avoid causing RFI. If deemed necessary, RF sources can be restricted from the more sensitive areas of a hospital, such as intensive care units.
Administrators of healthcare facilities can impose restrictions on the use of mobile RF transceivers. The concept of a specific minimum separation distance for each type of mobile transceiver has recently been proposed. For example, handheld cellular phones that radiate 600 mW would have to be kept at least one meter from a medical device that is immune to 3 V/m. A 3 Watt handheld transceiver would have to be kept 2.4 meters from the same device. In practice, an additional safety factor should be required to account for enhancement of signals by field reflections.
MedWOW offers an assortment of relevant RFI filtering solutions for many different types of medical equipment. Many types of hospital devices require filtering, so MedWOW's international inventories keep in stock much of what is required. If you don't find what you are looking for, MedWOW's Part Finder Service can locate what you need.
For more information on Electromagnetic Interference in Hospitals and RFI, make sure and follow the link in the resource box below.
Author Resource:-MedWOW. (www.medwow.com) is the leading international, online marketplace for buying and selling new and used medical equipment. The user-friendly website connects buyers, sellers and service-providers of medical equipment from all over the world, by combining multilingual customer support with comprehensive professional services and unprecedented reliability. MedWOW's value-added services empower your business!
